Atomic-absorption (AA) spectroscopy uses the absorption of light to measure the concentration of gas-phase atoms. It is the most widely used method for the determination of single elements in analytical samples.

Instrument: Varian - SpectrAA55 Atomic Absorption Spectrometer
Standards and samples are generally prepared in acid for best results. A “cookbook” is available for checkout from the manager, which provides suggested conditions for analysis of different elements.

Lamps available: Fe, Cu, Na, Mg, W, Mo, Tb, Gd, Co, P, Ir, Eu, Fe, Cd, Pt, Ni, Ca, Zn, Pb, Al and Pd.

Fluorescence spectroscopy is the optical emission from molecules that have been excited to higher energy levels by absorption of electromagnetic radiation. The main advantage of fluorescence detection compared to absorption measurements is the greater sensitivity achievable because the fluorescence signal has a very low background.

Instrument: Cary Eclipse Fluorescence Spectrophotometer
This instrument is equipped with a Xenon flash allowing the user to choose the collection mode of choice: fluorescence, phosphorescence or chemi/bio luminescence. The instrument has two monochromators, excitation and emission, and a photomultiplier tube detector.

Accessories available: A microplate reader accessory that measures 96 wells in less than 50 seconds and 384 in less than 90 seconds, and performs a full wavelength scan on each well within minutes. Also, a solid sample attachment, polarizers and a temperature-controlled cell holder are available for use.
User must provide cuvettes of choice.

In infrared spectroscopy, vibrational absorptions are measured. Fourier-transform infrared spectrometers offer the advantage of high sensitivity, resolution and speed of data acquisition.

Raman spectroscopy is based on the Raman Effect, which is the inelastic scattering of photons by molecules. Infrared (IR) and Raman spectroscopy both measure the vibrational energies of molecules but rely on different selection rules.

Instrument: Nicolet - Nexus 670 FT-IR and FT-Raman Module
This instrument has an Ever-Glo (black body radiation) light source and a XT-KBr beam splitter for near- and mid-infrared measurements and a polyethylene beam splitter for far-infrared measurements. The Raman module employs a Nd:YAG laser source at 1064 nm.

The detector for IR measurements is DTGS (deuterated triglycine sulfate) and for Raman, an InGaAs detector is used.

The user needs to provide IR-grade KBr for preparing pellet samples, or an appropriate liquid or mull-based cell.

Accessories: HATR (Horizontal Attenuated Total Reflectance): This accessory is ideal for highly absorbing materials such as aqueous solutions, rubbers and polymers (films).

Diffuse reflectance: The diffuse reflectance accessory can be used for most solids that can be put into a powder or crystalline state. Infrared KBr can be used for diluting solid samples and as a reference (supplied by user).

“Mass spectrometry is the art of ‘weighing’ individual atoms and molecules to determine their masses or molecular weights. Such mass or weight information is sometimes sufficient, frequently necessary and always useful in determining the identity of a species.” – John B. Fenn

Our instrumentation facility offers two GC-MS instruments, which are outlined below:

Hewlett-Packard G1800C Series II GCD System with HP ChemStation Software.
Ion source: Electron Impact (EI)
Mass analyzer: Linear Quadrupole
Detector: Electron Multiplier (EM)
Varian Saturn 2000 GC/MS
Ion source: Electron Impact (EI) and Chemical Ionization (CI)
Mass analyzer: Ion Trap
Detector: Electron Multiplier (EM)
Tandem mass spectrometry: (MS/MS)
Frequent users should provide their own GC syringes.

Instrument: Hewlett Packard, Series II, 1090 Liquid Chromatograph with HP ChemStation software.

This instrument has a diode array detector (200-600 nm) and a binary solvent delivery system.

Columns available: Waters C18, 4.6 x 150 mm column, Phenomenex C18, 4.6 x 300 (Bondapak & Bondclone), Chiral – AGP, 4.6 x 100 mm column, Agilent, Zorbax SB-CN, 4.6 x 150 mm column.

Available for use: solvent filtration system and filters (all mobile phases must be filtered), injection syringes.
User must provide solvents and mobile phases, and syringe filters for samples.

Ion exchange chromatography (IEC) is applicable to the separation of almost any type of charged molecule, from large proteins to small nucleotides and amino acids.

Instrument: Dionex ICS (Ion Chromatograph System) 1000
This instrument has a dual-piston pump, electrolytic suppression and digital conductivity detection. The AS14-A anion exchange column, with bicarbonate/carbonate eluent, provides sufficient separation of fluoride, chloride, bromide, acetate, nitrite, nitrate, phosphate and sulfate. In addition, there is an AS11-A anion exchange column that works with a sodium hydroxide eluent.
Columns available: Anion exchange column with membrane suppressor.

An ICP is a very high temperature (7000-8000K) excitation source that efficiently desolvates, vaporizes, excites and ionizes atoms. Molecular interferences are greatly reduced with this excitation source but are not eliminated completely. ICP sources are used to excite atoms for optical emission spectroscopy.

Instrument: Varian - Vista MPX, CCD Simultaneous ICP-OES

This instrument offers simultaneous measurement of approximately 75 elements from parts-per-billion to percent levels. Samples either can be introduced for analysis individually or by the use of an autosampler.

Available for use: Sample tubes for training and initial use. For additional use, sample tubes must be purchased by the user.

The use of thermal desorption in conjunction with gas chromatography (GC) assumes that some analytes of interest have been absorbed by some other material and, by heating them, they can be liberated from their matrix. Once desorbed, they are amenable to analysis by GC. This serves as a basis for the analysis of a wide range of complex sample types including environmental materials, fuel sources, foods, pharmaceuticals, polymers and many consumer products.
One advantage of thermal desorption of sample compounds to GC permits analysis of near 100% of the sample as opposed to an aliquot, which translates to an immediate increase in sensitivity.
Instrument: Bulk Dynamic Headspace Sampler System, CDS 8000 Concentrator

This instrument comes with bulk sampling accessory that permits outgasing/thermal desorption of large or irregularly shaped materials. Samples can be heated up to 3008C while the purge gas transfers the analytes to the built-in trap. After collection, the trap is heated to transfer analytes to the Varian Saturn 2000 GC-MS.

Accessory vessels: 95 mm x 110 mm vessel and a 38 mm x 128 mm bulk sampling vessel

Molecular ultraviolet/visible absorption by molecules generally occurs in one or more electronic absorption bands, each of which is made up of numerous closely packed but discrete lines. Each line arises from the transition of an electron from the ground state to one of the many vibrational and rotational energy states associated with each excited electronic energy state.

In condensed phase spectroscopy, these lines merge and appear as broad bands.

Instrument(s): The instrument facility has three Hewlett Packard 8453 UV-visible Spectroscopy Systems, each equipped with HP ChemStation software.

One instrument is equipped with a HP 89090A Temperature Control so the user can control the sample temperature, and the other two are equipped with a Sipper System. As stated in the accompanying operator’s manual, written by Agilent Technologies, “the Sipper System provides a simple method of improving the productivity and reproducibility of spectrophotometric analysis by eliminating the handling of cuvettes and the errors that can result in cuvette repositioning.”

These instruments offer:

UV-visible range: 200-980 nm
Light sources: deuterium and tungsten
Detector: diode array detector (2 nm/diode)